>> Software Compatible with Windows, Linux and Mac Operating Systems
The USB Multifunction USB-1608G high speed data acquisition device has 16 single-ended or 8 differential analog inputs, 8 digital I/O , 2 counter inputs and 1 external digital trigger input. The 16-bit analog inputs, controlled by the software, support input ranges of ±10 Volts, ±5 Volts, ±2 Volts and ±1 Volts per channel with a measurement rate of up to 500 k/s. The 8 Digital I/O connections are bidirectional and individually configurable for input or output. The digital trigger input has 2 software-selectable modes available: edge-sensitive or level-sensitive. The 32-bit counter inputs count TTL pulses up to a frequency of 20 MHz.
Check out the USB-1608G for a Measurement Sampling Rate of 250 k/s.
Check out the USB-1608GX-2AO for a Measurement Sampling Rate of 500 k/s and 2 Analog Outputs.
USB-1608G Series Includes Measurement Computing Software Suite:
>> TracerDAQ® Software
>> Universal Library for Visual Studio® and Visual Studio® .NET
>> DAQFlex Open-Source Software Framework for Windows, Linux and Mac Platforms
>> DasyLab and NI LabView Drivers
>> InstaCal Software Utility
NOTE: Large Quantity Discounts Are Available!
Note: Any order for Measurement Computing Products to be Shipped Outside the US will require an "End User Export Agreement" form to be Completed and Returned Prior to Products being Shipped.
High Speed USB Data Acquisition DAQ Specifications
Analog Input | A/D Converter Type: Successive Approximation ADC Resolution: 16 Bits Channels*: 8 (Differential); 16 (Single-Ended) Input Voltage Range*: ±10V; ±5V; ±2V; ±1V per Channel Input Impedance: 1GΩ (Power On); 820Ω (Power Off) Input Bias Current: ±10 nA Input Bandwidth: 870 kHz (All Input Ranges, -3dB Signal) Input Capacitance: 60 pf Sampling Rate*: 0.0149 Hz to 500 kHz Burst Mode**: 2 µs Throughput: 33 - 4000 S/s (Software); 500 kS/s (Hardware) * Software Selectable ** Software-Selectable Using the Internal A/D Clock; Always Enabled When using the External Clock (AICKI Command) |
Digital I/O | Digital Type: CMOS Number of I/O: 8 Configuration: Each bit Input or Output Transfer Rate: 33 to 8000 port Reads/Writes or Single Bit Reads/Writes Per Second Input High Voltage: 2.0 Volts (Min); 5.5 Volts (Max) Input Low Voltage: 0.8 Volt (Max); -0.5 Volt (Min); 0 Volt Recommended Output High Voltage: 4.4 V Min (IOH= -50uA); 3.76 Volt Min (IOH= -2.5 mA) Output Low Voltage: 0.1 V Max (IOL= 50uA); 0.44 Volt Max (IOL= 2.5 mA) Output Current: ±2.5 mA Max |
External Trigger | Trigger Source: TRIG input Trigger Mode: Edge or Level Sensitive, Rising or Falling Edge, High or Low Level Trigger Latency: 1 µs + 1 clock Cycle Max Pulse Width: 100 ns Min Input Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max) Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min); 0 Volt (Recommended) |
External Clock I/O | Input Clock Rate: 500 kHz Max Clock Pulse Width: 400 ns Min (Input and Output) Input Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground Schmitt Trigger Hysteresis: 0.4 Volt to 1.2 Volt Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max) Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min); 0 Volt (Recommended) Output High Voltage: 4.4 V Min (IOH= -50uA); 3.76 Volt Min (IOH= -2.5 mA) Output Low Voltage: 0.1 V Max (IOL= 50uA); 0.44 Volt Max (IOL= 2.5 mA) Output Current: ±2.5 mA Max |
Counter | Channels: 2 (CTR0 and CTR1) Resolution: 32-bit Counter Type: Schmitt Trigger, 33 Ω Series Resistor and 49.9 kΩ Pull-Down to Ground Schmitt Trigger Hysteresis: 0.4 Volt to 1.2 Volt Input Source: Terminal 52 (CTR0); Terminal 51 (CTR1) Read/Write Rates*: 33 to 8000 Reads/Wrires per Second Input High Voltage: 2.2 Volt (Min); 5.5 Volt (Max) Input Low Voltage: 1.5 Volt (Max); -0.5 Volt (Min) Input Frequency: 20 MHz Max High Pulse Width: 25 ns Min (Low and High) |
Timer Output | Type: PWM Output with Count, Period, Delay and Pulse width Registers Output Value: Default State is Idle Low with Pulses High, Software-Selectable Output Invert Internal Clock Frequency: 64 MHz Register Widths: 32-Bit Pulse Width: 15.625 ns Min (Low and High) Output High Voltage: 4.4 Volt Min (IOH @ -50 µA); 3.76 Volt Min (IOH @ -2.5mA) Output Low Voltage: 0.1 Volt Max (IOL @ 50 µA); 0.44 Volt Max (IOL @ 2.5 mA) Output Current: ±2.5 mA Maximum |
Memory | Data FIFO: 4kS (Analog Input); 2 kS (Analog Output) Non-Volatile: 32 KB (28KB - Firmware; 4KB User Data) |
Quiescent Current | 260 mA* * Includes 10 mA for Status LEDs. Doesn't include potential loading of Digital I/O Bits or +5 Volt Terminal |
Operating Range | Temperature: 0°C to 55°C Max Humidity: 0% to 90% RH Non-Condensing Max |
Storage Range | Temperature: -40°C to 85°C Max Humidity: 0% to 90% RH Non-Condensing Max |
Software Compatibility | Windows® 7, Vista, XP SP2+ (32-Bit or 64-Bit), Linux® and Mac® |
Dimensions | 12.7 cm x 8.9 cm x 3.5 cm (5.0" x 3.53" x 1.40") User Connection Length: 3 Meters (9.84 feet) Max. |
16 Channel USB Multifunction DAQ Module >> 16 Channel Analog Inputs Sampling Up to 500 k/s
>> 8 Digital I/O Channels, 2 Counter Inputs & 1 Timer Output >> Analog Input Measurement Ranges of ±10 Volts, ±5 Volts, ±2 Volts and ±1 Volts >> Includes TracerDAQ, DasyLab Drivers, DAQFlex and InstaCal Software |
Part #: USB-1608GX |
|
Optional Software | ||
TracerDAQ Pro Software >> Strip Chart, Oscilloscope, Function Generator and Rate Generator Software
>> Create Charts and Export Data |
Part #: TRACERDAQ-PRO |
|
DASYLab Lite DAQ Software >> Graphical Programming Software Package for Customized Applications Without Writing Code
>> Create Flow Charts Where Functions are Connected By Wires >> Available in 4 Versions (Lite, Basic, Full and Pro) >> Includes Hardware Drivers for Measurement Computing DAQ Devices |
Part #: DASYLAB-LITE |